Jieshou isolation clothing manufacturer supply
Appearance of medical isolation shoe cover: 1. The medical isolation shoe cover should be free of mold, and the surface should be free of impurities, adhesion, cracks, damage and other defects; 2. If the medical isolation shoe covers are sewn, the sewn parts should be firm, neatly formed, the needle size should be even and straight, and there should be no defects such as needle skipping and missing stitches. If the heat seal is applied, the heat seal parts should be firm, neatly formed, flat and free of cracks; 3. The sewing needle distance shall not be less than 6 stitches every 40mm. 4. Specification and size: the specification and size of the medical isolation shoe cover should conform to the size of the packaging bag logo, with a tolerance of ± 10%; 5. Surface moisture resistance: the water level on the outer side of the medical isolation shoe cover shall not be lower than the requirement of Level 2. 6. The breaking strength of type II medical isolation shoe cover shall not be less than 10N in longitudinal direction and 4N in transverse direction. 7 Elongation at break The elongation at break of type I medical isolation shoe cover material shall not be less than 10%. 8. Tensile strength Type I medical isolation shoe cover material tensile strength (longitudinal and transverse) shall not be less than 10Mpa. 9. Elastic belt performance The elongation ratio of elastic belt used for medical isolation shoe covers should be ≤ 1:1.7, and the tensile elastic recovery rate should be ≥ 75%. 10. Quality requirements: The weight of nonwoven cloth used in type II medical isolation shoe covers shall not be less than 15g/m2; The film thickness of type I medical isolation shoe cover shall not be less than 0.01mm.
Jieshou isolation clothing manufacturer supply
The correct steps for using disposable medical transfer pads to transfer patients with spinal injury are as follows: moving the injured: the operator conducts neck examination, judges whether the patient has respiratory tract injury, and then places the neck bracket. When placing the neck support, the middle radian of the neck support is clamped on the right shoulder of the patient and slightly tilted forward and downward. The neck support is placed first and then the front of the neck. The guarantee position is in the middle, and the buckle is buckled with moderate tightness. After the neck bracket is placed, the operator shall conduct a general physical examination from top to bottom, from trunk to limbs. Fasten the shoulder belt and the chest and abdomen fixing belt to ensure that the top of the movable breastplate is placed under the patient's armpit; The leg strap (black) goes around the injured person's knees from inside to outside and from bottom to top, clings to the groin, goes out from the inside of the thigh, pulls outward, buckles and tightens; The operator and the second assistant grasped the grips on both sides of the waist, and put the other hand under the leg of the injured person. The two hands clasped each other firmly, and the patient was rotated to 90 ° by 45 ° in two times.
Jieshou isolation clothing manufacturer supply
What's the function of medical cotton ball? The medical cotton ball is made of medical degreased cotton, which is white, soft and elastic white fiber, free of stains, stains, foreign matters, odor and taste. It is divided into sterile medical cotton balls and non sterile medical cotton balls. Medical cotton balls generally directly contact patients' wounds. They are the main sanitary materials used in the medical industry for patients' wound dressing, protection, cleaning and other purposes. They are non-toxic, non irritating, have good water absorption and are easy to use. Medical cotton balls have high requirements on sterilization. In addition, for the selection of raw materials for making cotton balls, the raw materials that meet the requirements of standards and industry standards must be selected. Medical cotton balls, including medical alcohol disinfection cotton balls and medical iodophor disinfection cotton balls, are made of medical degreased cotton balls dipped with a certain concentration of disinfectant, and are mainly used for sterilization of skin and mucous membrane of adults and children over 2 years old.
Jieshou isolation clothing manufacturer supply
Common problems of medical cotton balls: 1. When using cotton balls to reduce fever physically, pay attention to: the simple, reasonable and safe cooling method for patients with high fever is the physical method of reducing fever by wiping with 25% - 50% alcohol. After wetting with cotton balls, scrub the head and neck, limbs, back, hands and feet of the patient. Especially in the key areas to scrub the rich and colorful capillaries, such as armpit, elbow joint, armpit, groin, etc. Note that alcohol is not suitable for urticaria and other eruptive diseases. During the whole process of using alcohol cotton balls, prevent the secondary pollution caused by tweezers, cotton balls, cotton towels, etc. 2. The alcohol concentration value should be appropriate: after continuous experiments, we know that alcohol with a concentration of 75% has strong sterilization ability, so medical disinfection alcohol generally contains 75% pure alcohol and 25% water. The concentration value of alcohol is very critical. If it is too high or too low, it will weaken or even lose the disinfection and sterilization efficiency. Therefore, countermeasures must be selected to maintain the initial concentration value. Alcohol is easy to volatilize and cause the concentration value to decrease, so it should be stored in a very airtight container. This kind of situation often occurs: the cotton balls on the top of the utensils have been made for a long time, but some cotton balls on the bottom are still wet. Some people think that the wet part is alcohol. In fact, it is basically water, so it can no longer be used for disinfection and sterilization. 3. Don't use too much alcohol cotton balls: please don't use too much alcohol cotton balls in your daily life. The alcohol key has certain limitations on the practical application effect and efficacy time of common bacteria, so it is not necessary to blindly follow the trend of exaggerating the efficacy of alcohol sterilization. For example, for the cleaning of small toys, 84 disinfectant with effective chlorine must be used. Simply scrubbing with alcohol cotton balls will not have all practical effects; For the cleaning of tableware, the method of boiling at high temperature is more reasonable. 4. Special attention to the storage standard: when it is not suitable for cotton balls, it should be kept in a closed manner, stored in a dry and clean place, and placed in an area out of the baby's reach to prevent the baby from taking off the cotton balls and swallowing them by mistake.
Jieshou isolation clothing manufacturer supply
The "formula" of medical transfer pad has been widely exposed. There are so many kinds of raw materials: as long as it is a medical product, there are many stresses on the use of raw materials, even the medical transfer pad, a simple medical product, is no exception. Since medical transfer pads are usually used to transfer patients, there are very strict standards for the use of raw materials. At present, the materials commonly used in the production of medical transfer pads are PVC, polyurethane PU, ordinary silica gel, etc. Let's briefly understand the characteristics of different materials. The commonly used raw materials in the production of medical transfer pads are generally as follows: silica gel - alias: silicone rubber, transparent or milky white granular solid. It has open porous structure, strong adsorption, and can adsorb a variety of substances. If water is absorbed, the moisture absorption is about 40%. If cobalt chloride is added, it will be blue when dry and red after absorbing water. PVC is mainly composed of PVC powder, and other ingredients are added to enhance its heat resistance, toughness, ductility, etc. Alcohol and concentrated sulfuric acid are mixed 1:3 at 170 ℃ to produce ethylene chloride and ethylene, which will produce ethylene dichloride; Dichloroethylene can also be converted into chlorinated vinyl, which is the basic component of PVC. During polymerization, chlorinated vinyl molecules are linked together to form a PVC chain. The transfer pad made of this material is characterized by light weight, heat insulation, heat preservation, moisture-proof, flame retardancy, strong bending strength and impact toughness, and high elongation when broken. PU polyurethane is a common polymer material. Polyurethane is a new organic polymer material, which is widely used in many fields of national economy because of its properties. The product transfer pad made of PU material is mainly used in light industry, chemical industry, electronics, textile, medical treatment, construction, building materials, automobiles, etc. The casting polyurethane in polyurethane elastomer is used to produce anti-skid pads. The elastomer is a kind of polyurethane elastomer that is widely used and has a large output. The specific applications include printing and conveying rubber rollers; Molding cots; Oil seal, washer ball joint, bushing bearing; O-ring; Support pad; Sole, back root and toe cap; Lining; Gear, etc. The hardness range of elastomer selected is different in different application fields. The advantage of the transfer pad is its strong viscosity and adhesion. [For details, please refer to the relevant content of "Don't underestimate the mobile sliding pad component, its function is beyond your imagination!"] The above is a brief introduction to the characteristics of commonly used raw materials for the transfer pad. Our company specializes in producing all kinds of transfer pad products with reliable quality and excellent use effect. If relevant enterprises have the need to purchase this product by order, please call our hotline directly for consultation, and we will wholeheartedly provide services.
